Difference between revisions of "NG900/9-3VacuumLines"

From The Saab Tech Wiki
Jump to: navigation, search
Line 2: Line 2:
 
Vacuum lines and PCV components should be inspected every 30k miles or more often, and replaced as needed.  Rubber hoses become brittle with age, and deterioration and small cracks can be hard to see.  Original vacuum hoses are 4-mm inside diameter (ID), same size as most of the wiper washer hoses.  The same rubber hose is also used in the secondary air injection (SAI) system on n/a models.  I replaced all of mine around 100k miles, some for the second or third time.
 
Vacuum lines and PCV components should be inspected every 30k miles or more often, and replaced as needed.  Rubber hoses become brittle with age, and deterioration and small cracks can be hard to see.  Original vacuum hoses are 4-mm inside diameter (ID), same size as most of the wiper washer hoses.  The same rubber hose is also used in the secondary air injection (SAI) system on n/a models.  I replaced all of mine around 100k miles, some for the second or third time.
  
== Parts ==
+
== Repairing ==
 +
=== Parts ===
 
* Vacuum Hose
 
* Vacuum Hose
 
** 1a - 240 mm
 
** 1a - 240 mm
Line 17: Line 18:
 
** e - PCV check valve #7521313
 
** e - PCV check valve #7521313
  
== PCV Valve Hoses ==
+
=== PCV Valve Hoses ===
 
Part of the positive crankcase ventilation system.  This line leads from the valve cover to the engine intake.  In the picture at left, the stock 4-mm rubber hose is was replaced by a 4.8-mm reinforced fuel line.  It is less likely to clog, and lasts longer.  
 
Part of the positive crankcase ventilation system.  This line leads from the valve cover to the engine intake.  In the picture at left, the stock 4-mm rubber hose is was replaced by a 4.8-mm reinforced fuel line.  It is less likely to clog, and lasts longer.  
  
 
The check valve (PCV valve) needs periodic replacement.  The plastic valve cover nipple, grommet (bushing) and larger diameter hose may also need replacement if leaking oil.  
 
The check valve (PCV valve) needs periodic replacement.  The plastic valve cover nipple, grommet (bushing) and larger diameter hose may also need replacement if leaking oil.  
  
== MAP Sensor ==
+
=== MAP Sensor ===
 
Not the same part number and material as the other hoses (possibly silicone rubber from the factory).  It seems more durable, and should probably only be replaced by a compatible silicone hose.  It leads to the manifold air pressure (MAP) sensor.
 
Not the same part number and material as the other hoses (possibly silicone rubber from the factory).  It seems more durable, and should probably only be replaced by a compatible silicone hose.  It leads to the manifold air pressure (MAP) sensor.
  
== Fuel Pressure Regulator ==
+
=== Fuel Pressure Regulator ===
 
From the throttle body to the fuel pressure regulator (FPR).  The FPR is on the driver side of the fuel rail,  below the charge air pipe and behind a connector bracket.  The view on the left is from the driver side fender, and after unplugging the three connectors.  This line can be hard to inspect and replace because most of it is hidden under fuel rail wiring.
 
From the throttle body to the fuel pressure regulator (FPR).  The FPR is on the driver side of the fuel rail,  below the charge air pipe and behind a connector bracket.  The view on the left is from the driver side fender, and after unplugging the three connectors.  This line can be hard to inspect and replace because most of it is hidden under fuel rail wiring.
  
== Charge Air Bypass Valve ==
+
=== Charge Air Bypass Valve ===
 
Runs along the "charge air pipe" to the turbo bypass valve (BPV) at the front of the engine compartment.  This is the longest of the four hoses.
 
Runs along the "charge air pipe" to the turbo bypass valve (BPV) at the front of the engine compartment.  This is the longest of the four hoses.
  
== Evap System Purge Valve ==
+
=== Evap System Purge Valve ===
 
The purge valve hose for the Evaporative Emission System  connected to the throttle body is not an actual vacuum line (different size and material).  It allows fumes to be sucked from the charcoal canister in the wheel well into the intake and burned.  However, if the hose is broken, or the purge valve faults, the effect can be the same as a vacuum leak.
 
The purge valve hose for the Evaporative Emission System  connected to the throttle body is not an actual vacuum line (different size and material).  It allows fumes to be sucked from the charcoal canister in the wheel well into the intake and burned.  However, if the hose is broken, or the purge valve faults, the effect can be the same as a vacuum leak.

Revision as of 15:04, 28 October 2009

Overview

Vacuum lines and PCV components should be inspected every 30k miles or more often, and replaced as needed. Rubber hoses become brittle with age, and deterioration and small cracks can be hard to see. Original vacuum hoses are 4-mm inside diameter (ID), same size as most of the wiper washer hoses. The same rubber hose is also used in the secondary air injection (SAI) system on n/a models. I replaced all of mine around 100k miles, some for the second or third time.

Repairing

Parts

  • Vacuum Hose
    • 1a - 240 mm
    • 1b - 60 mm
    • 2 - 220 mm
    • 3 - 400 mm
    • 4 - 800 mm
  • PCV Components
    • a - Valve cover bushing #7515190
    • b - PCV nipple #9165903
    • c - Rubber hose #9189465
    • d - Generic 4-mm rubber hose, NAPA H-459
    • e - PCV check valve #7521313

PCV Valve Hoses

Part of the positive crankcase ventilation system. This line leads from the valve cover to the engine intake. In the picture at left, the stock 4-mm rubber hose is was replaced by a 4.8-mm reinforced fuel line. It is less likely to clog, and lasts longer.

The check valve (PCV valve) needs periodic replacement. The plastic valve cover nipple, grommet (bushing) and larger diameter hose may also need replacement if leaking oil.

MAP Sensor

Not the same part number and material as the other hoses (possibly silicone rubber from the factory). It seems more durable, and should probably only be replaced by a compatible silicone hose. It leads to the manifold air pressure (MAP) sensor.

Fuel Pressure Regulator

From the throttle body to the fuel pressure regulator (FPR). The FPR is on the driver side of the fuel rail, below the charge air pipe and behind a connector bracket. The view on the left is from the driver side fender, and after unplugging the three connectors. This line can be hard to inspect and replace because most of it is hidden under fuel rail wiring.

Charge Air Bypass Valve

Runs along the "charge air pipe" to the turbo bypass valve (BPV) at the front of the engine compartment. This is the longest of the four hoses.

Evap System Purge Valve

The purge valve hose for the Evaporative Emission System connected to the throttle body is not an actual vacuum line (different size and material). It allows fumes to be sucked from the charcoal canister in the wheel well into the intake and burned. However, if the hose is broken, or the purge valve faults, the effect can be the same as a vacuum leak.