Mbcullen at 08:51, 4 February 2010

2010-02-04T08:51:14Z

Mbcullen: Created page with '=Overview= The normally aspirated NG900's use a Motronic Engine Management System (EMS). When a Check Engine Light (CEL) shows, it indicates that there is a potential problem wit…'

2010-02-04T08:49:13Z

Created page with '=Overview= The normally aspirated NG900's use a Motronic Engine Management System (EMS). When a Check Engine Light (CEL) shows, it indicates that there is a potential problem wit…'

New page

=Overview=
The normally aspirated NG900's use a Motronic Engine Management System (EMS). When a Check Engine Light (CEL) shows, it indicates that there is a potential problem with the systems that are responsible for controlling the emmisions of the car. You can take it to the dealer and they will plug it into a computer to establish which part of the system is causing trouble, but if you want to get a rough idea of what the trouble is then you can use the following method.

=Retrieving Codes=
On the kick panel underneath the steering wheel, and in front of the pedals, you will see a rectangular piece of plastic. This is the socket that the dealer plugs their diagnostic equipment into. Remove the cover and you will see that it has two rows of 8 connectors (See below)

[[File:Flash_code_socket_motronic.gif‎|thumb|none|Motronic Flash Socket]]

# Get a piece of insulated electrical wire and strip back the insulation about 5mm at each end. Insert one end of the wire into the socket for pin 6 (this is highlighted in red above)
# Find a suitable place on the bodywork that you can ground the other end of the wire too (DO NOT ground it yet!)
# Turn the ignition on and ground the wire for between 0.5 and 4 secs.
# The CEL will now flash in two stages. Count the first set of flashes and then the second set. The two will make up the two digit number that you are looking for. e.g. 4 flashes followed by 1 flash equals 41.
# Refer to the tables below to establish what the code means.

==Motronic 2.10.2 (4 Cyl. engines)==
Flash code Function
11 Relay, secondary air injection
12 No fault
21 Mass air flow sensor
41 Coolant temperature sensor
51 Throttle position sensor
61 Oxygen sensor
72 Adaptation, long time
73 Adaptation, short time
81 EVAP canister purge valve
91 Control module fault (RAM)
92 Control module fault (ROM)

==Motronic 2.8.1 (V6 Engines)==
Flash code Function
11 Relay, secondary air injection
12 No fault
21 Mass air flow sensor
31 Intake air temperature sensor
41 Coolant temperature sensor
51 Throttle position sensor
61 Oxygen sensor, Cyl. 1-3-5
62 Oxygen sensor, Cyl. 2-4-6
71 Adaptation, Cyl. 1-3-5 (rich/lean)
72 Adaptation, Cyl. 2-4-6 (rich/lean)
81 EVAP canister purge valve
91 Control module fault (RAM/ROM)

@@ Line 16: / Line 16: @@
 ==Motronic 2.10.2 (4 Cyl. engines)==
   Flash code  	Function
-	            Relay, secondary air injection
+	        Relay, secondary air injection
-	            No fault
+	        No fault
-	            Mass air flow sensor
+	        Mass air flow sensor
-	            Coolant temperature sensor
+	        Coolant temperature sensor
-	            Throttle position sensor
+	        Throttle position sensor
-	            Oxygen sensor
+	        Oxygen sensor
-	            Adaptation, long time
+	        Adaptation, long time
-	            Adaptation, short time
+	        Adaptation, short time
-	            EVAP canister purge valve
+	        EVAP canister purge valve
-	            Control module fault (RAM)
+	        Control module fault (RAM)
-	            Control module fault (ROM)
+	        Control module fault (ROM)
 ==Motronic 2.8.1 (V6 Engines)==
   Flash code  	Function
-	            Relay, secondary air injection
+	        Relay, secondary air injection
-	            No fault
+	        No fault
-	            Mass air flow sensor
+	        Mass air flow sensor
-	            Intake air temperature sensor
+	        Intake air temperature sensor
-	            Coolant temperature sensor
+	        Coolant temperature sensor
-	            Throttle position sensor
+	        Throttle position sensor
-	            Oxygen sensor, Cyl. 1-3-5
+	        Oxygen sensor, Cyl. 1-3-5
-	            Oxygen sensor, Cyl. 2-4-6
+	        Oxygen sensor, Cyl. 2-4-6
-	            Adaptation, Cyl. 1-3-5 (rich/lean)
+	        Adaptation, Cyl. 1-3-5 (rich/lean)
-	            Adaptation, Cyl. 2-4-6 (rich/lean)
+	        Adaptation, Cyl. 2-4-6 (rich/lean)
-	            EVAP canister purge valve
+	        EVAP canister purge valve
-	            Control module fault (RAM/ROM)
+	        Control module fault (RAM/ROM)

NG 900/9-3 Motronic CEL Flash Codes - Revision history

Mbcullen at 08:51, 4 February 2010

Mbcullen: Created page with '=Overview= The normally aspirated NG900's use a Motronic Engine Management System (EMS). When a Check Engine Light (CEL) shows, it indicates that there is a potential problem wit…'